Quick Answer: Will a 360 transmission fit a 318 motor?

It will fit no problem. The 318 is an internally balanced engine verses the 360 being an external balanced engine. Both engines will have a 727 Torque Flight transmission.

Are 318 and 360 blocks the same?

Nope, not the same. Bore size 318 is 3.91. Bore size 360 is 4.00. Crank is different as well.

Will a 360 intake fit a 318?

The 360 heads and Intake swap will fit on the 318, but the compression will be around 7.2:1, which is not very good for performance, which is not to say that the heads cannot be shaved . … The book says the 360 to 318 works well, but, take the 318 heads, shave .

Are 5.2 and 5.9 transmission the same?

There not interchangeable. Other then that,it’s the same. Ask for the build sheet for the 5.2 and the 5.9 then you’ll know the difference.

Is a 318 a good motor?

The 318 engine is absolutely the best all-around small block Mopar, in my opinion. It can easily make 400 plus horsepower and still has great street manners. … Each are good engines, but for performance use, you should stick with the LA or Magnum because performance parts for the 318 Poly are hard to find.

IT IS INTERESTING:  Are Toro engines any good?

What engine is better 318 or 360?

The advantage of the 360 over the 318 for a street/strip engine is the obvious cubic inch advantage, the longer stroke crank has more leverage for more torque, and the larger bore size lets you use cylinder heads with larger valves for more airflow.

How do I know if I have a 318 or 360?

The 360/5.9 is externally balanced, so if you look at the harmonic balancer pulley you will see a weight cast into the design. The 318 is internally balanced like most engines are, and its harmonic balancer pulley will be ‘symmetrical’ without any balance weight built-in.

How much HP does a 318 have?

The 318 four-barrel, used on police pursuit and other cars, produed 165 hp and 240 lb-ft of torque.

Will a 340 intake fit a 318?

Yes, you can port match, but it does work much better to build a 318 well so the 340/360 parts work well on it. I have even seen people with 4×4’s to use 318 heads on their 340/360 to try for better low end torque.

Is a Dodge 360 a good motor?

The Mopar 360 can make an excellent performance engine. It was introduced with a 2-bbl carburetor in 1971. Not intended as a performance engine, it also featured a cast crankshaft and low compression ratio (8.5 to 1) cast pistons. … In spite of this rocky start, the 360 can be built into an excellent street engine.

Is the Dodge 5.2 a good motor?

The 5.2 is a great motor. Easy to work on, lots of aftermarket (not as much as a 302 or 350, but a close third), and quite tough. Fuel economy isn’t as good as the 4.7 and power (stock) is about the same.

IT IS INTERESTING:  What is the hardest course in civil engineering?

What is the difference between a 42re and an 44re transmission?

The difference is how much torque they can handle. The 44 is a bit stronger than the 42. They have the same gear ratios. The 46 RE has a larger housing and a different 1st and 2nd gear.

What vehicles have the 46re transmission?

A518 (46RH/46RE)

  • Dodge Ram pickup and vans 150/250/350 V8 and diesel engines (DGT)
  • Dodge Ramcharger SUV 1988-1993 5.2L & 5.9L V8.
  • Jeep Grand Cherokee 1993 5.2L, 1998 5.9L.
  • 1996 Dodge Dakota V8 (Also 98-03 Dakota 5.9L R/T)
  • 1998-2003 Dodge Durango 5.9L V8 (4WD or 2WD)
  • 1998–2003 Dodge Dakota R/T.

How many miles will a 318 last?

Like any engine, it depends on routine maintenance and how the engine has been treated over its lifespan. Some may last 2 miles, some 400,000 or more.

How much does it cost to rebuild a 318 engine?

I rebuilt a 318 last year. Cost me around $3000 and is around 300 hp.23 мая 2016 г.

How much boost can a stock 318 handle?

You shouldn’t run any boost without the right fuel and no more than 4 PSI without dealing with timing. A 318 with many rigs out there is running as much as 25 PSI.

Car service